Biofilter Suppliers for RAS — Buyer's Knowledge Page
The biofilter is the nitrifying heart of a RAS. Under-size it and biology destabilises; over-size it and CAPEX and pumping energy skyrocket. Buyer's job: define TAN removal rate needed (from mass-balance) and let vendors propose media and geometry.
FishMatch Group is supplier-neutral. This page is educational content for buyers — not legal advice, not a supplier ranking.
Typical applications
- Fresh, brackish and full-salinity RAS
- Nursery, grow-out, broodstock loops
- Post-smolt salmon and marine finfish
Project sizes
- Small: 10–50 kg TAN/day removal
- Mid: 50–500 kg TAN/day
- Large: 500–5,000+ kg TAN/day
Selection criteria
- Guaranteed volumetric TAN removal at your temperature and salinity
- Media specific surface area (m²/m³) and clogging behaviour
- Hydraulic residence time and back-mixing
- Head loss and pumping energy
- Start-up curve and inoculation protocol
Questions buyers should ask
- What is guaranteed VTR (g TAN / m³ media / day) at 15°C / 20°C / 25°C?
- What is the biofilter's contribution to total specific energy?
- How is media replaced and how often?
Common procurement mistakes
- Trusting media catalog VTR without temperature correction
- Ignoring salinity effects on nitrification kinetics
- Under-sizing degassing after the biofilter
RFQ recommendations
- Tender against a required TAN removal load, not a media type
- Ask for kinetic model and CFD if project is large
Related tools & guides
Calculators
Buyer's Guides
Project templates
Regulations & standards
Frequently asked questions
Next steps
Turn this knowledge into a bankable project.
Get the RFQ checklist for “Biofilter Suppliers”
Leave your details and we’ll route you straight into the RFQ Builder with a checklist pre-filled for this topic. Prefer WhatsApp? The same brief opens in one tap.
Short answer
How do you find and compare Biofilter Suppliers suppliers?
You publish one structured requirement instead of contacting vendors one by one. FishMatch Group turns your Biofilter Suppliers brief into a technical RFQ, runs it against qualified international manufacturers, integrators and EPC contractors, and returns normalised quotations you can compare on scope, lead time and total cost of ownership. Supplier identities stay confidential until both sides are qualified and agree to proceed.
- Coverage:
- Vetted manufacturers, integrators and EPC contractors across 40+ countries
- Typical turnaround:
- Depends on scope and site data; no turnaround is guaranteed
- Confidentiality:
- Buyer and supplier identities stay private until both sides agree
- Cost to buyers:
- No fee charged to the buyer
Before you request quotes
Equipment scope
What equipment does a commercial aquaculture project actually need?
A grow-out project typically needs holding infrastructure (tanks, ponds or cages), water movement (pumps, piping, valves), aeration or oxygenation, water treatment appropriate to the system, feeding equipment, grading and handling gear, monitoring and alarms, and backup power. RAS adds mechanical filtration, biofiltration, degassing, disinfection and tighter process control. Hatchery and processing scopes are specified separately.
Which equipment should be specified before requesting quotes?
Specify the items whose sizing changes everything downstream: design biomass and stocking density, water exchange or recirculation rate, oxygen demand at peak temperature, and installed pumping head. With those four fixed, suppliers can quote aeration, filtration, pumps and power on the same basis. FishMatch calculators produce these figures and attach them to the RFQ.
Can equipment be sourced in stages?
Yes, and phased procurement is common. The usual sequence is water supply and holding infrastructure, then aeration and treatment, then automation and monitoring, then processing and cold chain. Staging works when interfaces and capacity headroom are defined at the start; otherwise later phases force replacement rather than addition.
Supplier selection criteria
How should a buyer compare aquaculture suppliers?
Compare on evidence, not on presentation: delivered projects at a similar scale and climate, engineering support during design, lead time commitments, spare-part and service availability in your region, certification and testing documentation, payment and warranty terms, and willingness to quote against your specification rather than substituting a catalogue package.
What are the warning signs in a supplier quotation?
Treat these as review triggers: no itemised scope, guaranteed biological or financial performance, no named delivery terms or lead time, no spare-parts or service statement, unclear responsibility for installation and commissioning, and equipment sizing that does not reference your water temperature, oxygen demand or biomass targets.
How does FishMatch handle supplier selection?
FishMatch is an independent sourcing layer, not a manufacturer or reseller. Requirements are structured into a single technical RFQ and routed to relevant producers; buyers receive comparable offers without supplier identities being exposed before they choose to proceed. Selection stays with the buyer — FishMatch standardises the comparison basis.